This system was removed from service and packaged up by the technician. It is ready to ship.
5' x 12' Table
Includes: Schmalz Vacuum, Southworth Scissor Lift and Vacuum Pump
Hours of the machine: Power on time is 21,039 hours, Operating time is 5,908, cutting time is 3,095. Very low hours. The vacuum pump has 6,034 hours on it.
One (1) 18HP (13.5KW ), 4 Pole “Cartridge” Spindle with HSK F63 Chuck, programmable RPM up to 24,000, synthetic grease lubricated “Quad” ceramic bearings, a safety device for automatic fault detection, and a maximum tool shank diameter of 1".
One (1) Programmable Air Blast Nozzle at the spindle.
Spindle with Traveling Tool Changer Spindle Cartridge
TOOL CHANGER One (1) HSK F63 “Twelve Station” Automatic Tool Changer Carousel “Dynamic” carousel is attached to the spindle tooling plate (allowing back ground tool change while drilling) with a safety device for automatic fault detection. The maximum tool diameter capacity is 8″ per pocket with adjacent pockets empty and 4" with all pockets full. Total carousel weight capacity of 120 lbsOne (1) Tool Changer Carousel Dust Shroud
VACUUM SYSTEM One (1) 40 HP liquid ring vacuum system with a 10 micron inlet filter. The recirculation oil-vane type pump supplies a maximum of 29.3 Hg vacuum (98% absolute vacuum) to two independent ports on the worktables) at a maximum flow of 520 cfm. One (1) heavy duty exhaust/reclaim muffler-filter ensures quiet and clean operation. Vacuum Voltage: 460 volts, 3-Phase – 52 AMPS DRILLING UNIT One (1) dedicated 2.5 HP, 19-Spindle, L-Shaped Flexible Drilling Unit, with thirteen (13) vertical spindles (5 x 8) and three (3) double-ended horizontal spindles (2 x 4); 4000 RPM; 32mm pitch; independent selection Color LCD Touch Screen Monitor Control Pedestal with Remote MPG Fanuc CNC Control System Panel I Features Intel Processor ‐ Windows 7 Operating System 12.1" Color LCD ‐ Touch Screen Control Panel Panel I Memory 2GB RAM 40 GB Hard Drive / DVD‐ROM Disk Drive Network Ready (Includes Card) CNC Features Operation Automatic operation (Memory) MDI Operation & DNC Operation Schedule function Program number search Sequence number comparison and stop Wrong operation prevention Buffer register / Single block JOG feed Manual reference position return/shift Full Function Manual handle feed (Remote MPG wheel) Feed Function Rapid traverse/Feedrate override Cutting federate clamp Automatic acceleration/declaration Rapid traverse bell‐shaped acceleration/deceleration Linear acceleration/deceleration after cutting feed interpolation Automatic corner deceleration (Look Ahead Control) Feedrate control with acceleration in circular interpolation AI advanced preview control Program Input Tape code Optional block skip External memory and sub program calling function Absolute/incremental programming Diameter/radius programming Plane selection Automatic coordinate system setting Workpiece coordinate system/preset Addition of workpiece coordinate system pair Direct input of workpiece origin offset value measured Optional chamfering/corner R Programmable parameter input Subprogram call Custom Macro B Interrupting type custom macro Canned cycles for drilling/ Small‐hole peck drilling cycle Circular interpolation by R programming Automatic corner override Coordinate system rotation Programmable mirror image Full Keyboard/Mouse Ports (Two (2) PS/2) One (1) Parallel Port Fiber Optic Interface with CNC Controller (HSSB) Two (2) USB Ports Two (2) Serial/RS232 Ports Axis Control Axis Control by PMC Axis Synchronous/ Simultaneous Control Position Switch Interpolation Functions Nano interpolation Positioning/Single direction positioning Exact stop mode Cutting mode Linear, Circular, Cylindrical and Helical interpolation Dwell (G4) High‐speed skip Auxiliary/Spindle Speed Function Auxiliary function 2nd auxiliary function Spindle analog output Spindle Override Dry Run Tool function/Tool compensation Tool offset memory (400 pairs) Tool radius/Tool length compensation Tool length measurement & Cutter compensation Inch/Metric compatibility Accuracy compensation function Backlash compensation Store pitch error compensation Editing Operation Part Program Storage Size (512K) 400 Total Registered Programs Part program background and extended editing Program protect Setting and Display Current position display Alarm Message/Alarm History display Operator Message/Operator History display Run hour and parts count display Actual cutting federate display Maintenance information screen One (1) Button Work Surface Milling & Part Program Orientation One (1) Dust Shroud Pushbutton Override for Safety
|Model||5' x 12' CNC Router|